SOLD AS A COMPLETE KIT FOR THE PROJECTOR HEADLIGHTS - Works as low beam and high beam.
The 2014 - 2015 GMC Sierra with factory projector headlights is actually a tricky vehicle to install upgrade lighting into. Not because the bulbs don't fit or the install is actually difficult, but because the vehicle uses a complex PWM/CANBUS system to monitor and control the headlight function. If you don't use an HID ballast built to integrate with this type of system you will get problems such as "bulb out" error warnings on your dash, flickering, or the headlights will just turn off! This is very common with LED headlight bulbs, and most aftermarket HID kits. Some HID kits can be made to work with an external CANBUS module of some kind, but now the GTR Lighting GEN 5 PWM/CANBUS HID conversion kit is available, and it is super bright and totally plug and play! No need for extra harnesses, no splicing wires, just plug and play. Watch our install video to see how easy it is to do the install!
The 14-15 GMC Sierra projector headlight is a cool setup - it uses a single beam bulb (9012, 1 filament) but creates both your high and low beam patterns separately. The headlight accomplishes this by activating an internal solenoid that moves a cut off shield inside the projector. When the shield is up, you get a low beam pattern with a cut off line. When the shield is down and out of the way you get all the light and a wide flood high beam. This HID kit replaces your original halogen bulb with HID to get both high beam and low beam, 500% brighter than stock!
Super Fast Start-Up Ballast
Are you sick of a slow ballast warm-up time? The GTR Lighting Slim PWM has an instant startup like new OEM ballasts of only 0.1s with full brightness reached at 9s.
This ballast is barely larger than a stack of credit cards. 3.5" long, 2.75" wide and a half-inch tall! Mounting is easy with the supplied bracket with tape and ground strap.
NOT ALL HID KITS ARE CREATED EQUAL!
When you purchase a GTR Lighting HID conversion kit for your vehicle you're getting the best of the best in terms of wire harness, connector, bulb and ballast quality. People all over the world trust GTR Lighting for being the pinnacle in quality for HID conversion kits. Our aftermarket ballasts are built with the highest quality components designed to last for 2,500 hours of use and provide up to 5,000 Lumen of light per HID bulb! Our bulbs provide a faster-than-average warmup time, and produce less operational noise when compared to other brands.
The GTR Lighting bulbs are constructed to be the best of the best as well. We use the best aftermarket connectors, silicone wiring, and HID bulb capsules available to create a product that just works and works well. Our bulbs have the ability to produce 30% more light than budget-brand HID bulbs found elsewhere. It's not uncommon to hear stories about how after a customer switches to a GTR Lighting HID kit it's twice as bright as their old HID kit they got from somewhere else!
55w Slim PWM/CANBUS HID Ballast Specs:
- Power Input Voltage: 9-16V DC
- Output Wattage: 55W
- Input Current: 4.4A @ Startup @ 14VDC
- Ignition Voltage: 23KV
- Operating Temperature: -40C to +85C
- Lifespan: 2,500 Hours
- Dimensions: 3.5" x 2.75" x 0.5"
- Weight: 0.65lb
- Cord Length: 13"
- Wiring Input: Universal Female Socket (9006 Bulb Style/ P22D base)
- Wiring Output: Universal AMP style, 1 male, 1 female
PWM stands for Pulse Width Modulation, it's when the vehicle flashes the input voltage to your bulbs so fast that you can't see the difference, but it modulates the activity of the halogen bulb. That's fine on an old style halogen/incandescent, but on HID systems it might make a flashing or strobing effect, or not work at all. The proprietary technology used in the GTR Lighting GEN 5 Smart System HID ballast integrates with all PWM and CANBUS vehicles for optimal functionality.
The key component of all HID ballasts is the controller used to manage all functions including ignition, protection, and constant use. Whatever type of controller is used is what dictates the quality level of the ballast. There are two kinds of controllers used inside HID ballasts:
1. CPU Controller -or- 2. ASIC Controller
A standard CPU controller is the most common contruction type for aftermarket ballasts becuase it is simple, common and cheap to produce. It requires very little quality control or strict design to function, therefore it's easy for ballast makers to create low quality CPU controlled products. It isn't very hard and it is very cheap to build. They work OK when made with high quality components but this is not often the case. A CPU controller lacks the ability to monitor the HID lamp (as the lamp power-decay changes over time) so it can cause short lifespan from overpowering, or low light output from underpowering. Generally speaking the defect rate of a CPU Controller based ballast is high, and the lifespan is shorter.
An ASIC controller like what's used in the GTR Lighting GEN 4 ballast is what you'll find in an OEM ballast for intelligent bulb control. The ASIC-based ballast technology is sophisticated, complex and intuitive. The Hylux ASIC technology will react to the bulb response to power and increase or decrease output to keep the bulb running bright for the longest possible time. ASIC technology also allows the ballast to have a higher level of CANBUS integration for vehicles that use PWM control or adaptive lighting. It's not a 100% fix for every vehicle, but the technology is designed to be the most flexible and work with the most applications easier. HID ballasts that use Hylux ASIC technology are also more expensive to make because the components required to build this system are high quality - you can not make a cheap ASIC ballast, therefore everything about a Hylux ballast is better: Faster warmup time, less ignition noise, brighter stable operating light, less flicker-fluctuation and a longer lifespan. Simply put, the GTR Lighting HID ballasts with GEN 4 Hylux technology are the best aftermarket ballast available.
GTR Lighting HID Bulbs:
Power Input Wattage: 55w
High-Grade Silicone Wiring
Precisely Machined Bulb Bases
Ceramic-Insert Bulb Base for Increased Heat Resistance
Precise Fitment like OEM Bulbs
Precise Xenon-Capsule Chemical Mixture for Vibrant Color Creation
HID Wire: 7.5" Adapter: 13"
We use ultra high quality 100% Quartz glass to construct the main bulb component. The glass houses an OEM-grade xenon capsule using high quality halide salts from our materials supplier. Our bulbs use an OEM-inspired mounting and alignment system to keep the bulb perfectly centered where it needs to be - this is probably the most important aspect of why GTR Lighting bulbs are the best of the best. If your bulb is misaligned at all it will cause dim light output, shadows and poor beam patterns.
If your vehicle uses a CANBUS system to control and/or monitor the bulbs or if your vehicle uses a PWM system to control the bulbs, this GEN 5 ballast kit will be your best bet at perfect, plug and play operation. Nothing is guaranteed to work all the time because vehicle manufacturers are constantly updating the technology they use to operate and monitor the different lighting systems, but so far this new GEN 5 PWM/CANBUS ballast has integrated perfectly with everything we've tested it on, including Ram trucks, Mercedes cars, Chrylser cars, GMC trucks, and new Ford trucks.
This HID kit uses single beam HID bulbs with a built-in adapter wiring harness. Single beam are the type of headlight or fog light bulbs that have 1 filament per bulb. If your car or truck has 2 light bulbs per headlight housing and one does low beam, the other does high beam - you've got single beam bulbs! Same goes for fog lights, nobody has ever built a car or truck with a dual beam fog light bulb... NOTE ABOUT PROJECTORS: Some projector-based headlights use a single beam inside the projector and use an external actuator to control a shutter inside the housing to create a high beam/low beam effect, all the while using a single beam bulb... That means it's possible to have a single beam bulb control both high and low beam but only in SOME projector headlight applications. (e.g. Dodge Ram uses a single beam bulb + a dual beam Projector. Toyota Tacoma uses a single beam bulb + a single beam projector). This kit is designed to plug into your factory headlight wiring to control the new HID bulbs and ballasts.
GTR Lighting HID bulbs are designed to be a perfect fit replacement for any respective halogen/incandescent headlight or fog light bulb. We support the most common bulb types and some uncommon ones too! GTR Lighting HID bulbs are precisely engineered to work the best, brightest, and have the longest life time when used in conjunction with GTR Lighting HID ballasts, but they can also be used with most aftermarket HID ballasts. If you're unsure of which HID bulb style you need, please email us for assistance.
Included in this Kit:
- 2 GTR Lighting Slim PWM 55w HID Ballasts
- 2 GTR Lighting Single Beam HID Bulbs with integrated adapter wiring
- Install Instructions
- Retail Display Box
All GTR Lighting HID components are covered under our world famous "No Questions Asked" Lifetime Warranty - if it breaks we'll fix it or replace it! For more details visit the warranty definitions section HERE.